WEAVEPOINT 6 DOWNLOAD FREE

It is important to select Total Repeat if you work with complex color sequences and especially if the repeat does not match the liftplan repeat. Tabby Plain Weave Change to tabby plain weave weaving. And check that you have selected the correct Com Port - being the port where the loom cable is connected to your PC. The two arrows inside the squares will advance the Scrolling Grid, as currently displayed in the window, to the next page of the pattern. Note that this sound can be changed in the Control Panel Sounds to any sound you like. If, for whatever reason, you find it necessary to go from one connection type to the other, it is best to change the protocol, then reboot the Compu-Dobby IV and restart WeavePoint. WeavePoint will then store the connection information and use this the next time you start Loom Control.

Uploader:	Akijora
Date Added:	2 January 2011
File Size:	50.78 Mb
Operating Systems:	Windows NT/2000/XP/2003/2003/7/8/10 MacOS 10/X
Downloads:	14933
Price:	Free* [*Free Regsitration Required]

Each time you exit from weaving, the screen saver will be re-enabled.

Women's footwear Shoes | Next India

The longer your repeat, the more will be shown, but the weavepoimt will be limited to the range allowed in the upper left corner.

To download a trial version of WeavePoint Complex Drafting, click here.

The present position, repeat range, and weaving direction will be stored. Here you can weavepoijt the total number of picks weavepojnt the repeat to weave, the total number of picks you have woven since you started the present weaving session and the next, present, and last picks, and the position of the cursor if it is over a shaft in the Liftplan. If you change the name of your design, it might not save it correctly.

WeavePoint | Weaving software

When Reverse is in effect, a large, red arrow will appear to the right of the Active Pick number in the lower right corner. Then test the sound with Preview.

Total Repeat should be selected so the full range will repeat automatically when weaving. Total Repeat is the minimal repeat one has to select to get the design repeated completely, including color and pattern.

Patterns and can accommodate up to picks. An AVL Cartridge window appears on the screen. Weaving with a Cartridge: The computer will automatically choose a COM port number for the adapter. When saving, you can later choose Resume to continue weaving the same pattern.

If, for whatever reason, you find it necessary to go from one connection type to the other, it is best to change the protocol, then reboot the Compu-Dobby IV and restart WeavePoint. If errors occur, check that the cable is properly connected at both ends. Note that the present pattern will be saved to disk like an ordinary WeavePoint pattern. It affects the timing of the solenoids with the movement of the Slide Bar in the Dobby Box. If it is important to access any pattern stored weaveloint the cartridge, you wevepoint click No and then try to load the pattern from the cartridge.

It will scroll as you progress through your extended pattern.

You are ready to start weaving. For further information, refer to your Compu-Dobby manual.

Complex Drafting is tuned especially for making patterns with more than one shaft weavepojnt. Enter a pattern name of up to twelve characters, if you did weavepint name it before. For weaving a pattern with weft borders, you can select Start Pick to be the first pick above the border. Click the tabby button again to leave tabby weaving and return to your pattern. Use your cursor and right click to make any changes.

It is also possible to make normal tie-up and liftplan patterns with only one shaft group, but note that standard WeavePoint is much more flexible for this purpose.

After step 5, go to the appropriate part. Note that this sound can be changed in the Control Panel Sounds to any sound you like.

If your repeat is short, 16 for example, it will be a narrow horizontal selection of your pattern. The two Up and Down Arrows will cause the next pick to move up or down as you select, and the number of the next selection is always displayed weavepolnt the box between the two sets of arrows. If you try to save a design in a tie-up mode, you will get a warning message to transform it to a liftplan mode.

This box will allow you to select your type of Compu-Dobby, Connection Type and other options that will provide tools to help you while weaving. Here you decide in which position on your cartridge you want to put this liftplan.